[clamav-users] File::Scan::ClamAV
Chris
cpollock at embarqmail.com
Tue Jul 22 18:11:12 UTC 2014
On Tue, 2014-07-22 at 17:19 +0100, Anthony DIckinson wrote:
> On 22/07/14 16:33, Chris wrote:
> > On Tue, 2014-07-22 at 13:53 +0100, Anthony DIckinson wrote:
> >> On 22/07/14 03:47, Chris wrote:
> >>> On Sun, 2014-07-20 at 12:52 -0400, Scott Kitterman wrote:
> >>>> On Sunday, July 20, 2014 07:27:25 Chris wrote:
> >>>>> On Sun, 2014-07-20 at 13:32 +0200, Matus UHLAR - fantomas wrote:
> >>>>>> On 19.07.14 21:38, Chris wrote:
> >>>>>>> Finally I'm about finished with setting up my Ubuntu 14.04 system and
> >>>>>>> getting everything setup the way it was in the old Mandriva system. I
> >>>>>>> have both SA and ClamAV running now but I'm missing a module,
> >>>>>>> File::Scan::ClamAV to interface with SA. Have tried multiple times to
> >>>>>>> install via CPAN, I'm posted the output at pastebin -
> >>>>>>> http://pastebin.com/bdurgL6X
> >>>>>>>
> >>>>>>> Any ideas anyone? ClamAV has been installed via the Ubuntu software
> >>>>>>> installer if it makes a difference.
> >>>>>> why not using ClamAV with your MTA directly?
> >>>>> Good morning Matus, I have postfix installed and running, however, the
> >>>>> only mail that goes through it are the outputs of cronjobs sent to me
> >>>>> and the forwarding of spam to the address spam at uce.gov . That is
> >>>>> probably overkill but I installed it so long ago on the old machine that
> >>>>> it was just 2nd nature to install it again. The mail from my ISP comes
> >>>>> in via Fetchmail > Procmail and is run through SA prior to getting
> >>>>> tossed to my inbox.
> >>>> I use clamsmtp (also from the Ubuntu package archive) with postfix, but I
> >>>> suspect you could configure it as a transparent proxy between fetchmail and
> >>>> procmail. Then the virus scanning would be handled further upstream.
> >>>>
> >>>> Scott K
> >>> I looked at this Scott but I don't think I'm techno-savy enough to try
> >>> it. Any other ideas on how to install this module? After looking at the
> >>> 't' folder in the source pkg and the errors it looks like it's looking
> >>> for something it can't find but then again I'm not a perl programmer so
> >>> I can't be positive.
> >>>
> >>> Thanks
> >>> Chris
> >>>
> >> Chris,
> >>
> >> Looks like the tests for this module are out of date or not 100%
> >> accurate. You can get the tests to complete by fudging.... Warning: Hack
> >> alert!!!
> >>
> >>
> >> #step 1
> >> sudo cpan
> >> install File::Scan::ClamAV
> >> (this will fail)
> >> look File::Scan::ClamAV
> >> (this puts you in the build directory for this module within cpan) e.g.:
> >>
> >> cpan[2]> look File::Scan::ClamAV
> >> Running look for module 'File::Scan::ClamAV'
> >>
> >> Trying to open a subshell in the build directory...
> >> Working directory is /root/.cpan/build/File-Scan-ClamAV-1.91-O_dSGE
> >> xxxx at xxxx:.cpan/build/File-Scan-ClamAV-1.91-O_dSGE#
> >>
> >> #step 2
> >> cd t
> >> (go into the test directory)
> >> (in mkconf.pl change):
> >> my $dir = cwd;
> >> to
> >> my $dir = '/tmp/;
> >>
> >> #step 3
> >> In 01ping.t, 02reload.t, 03quit.t, 04scan.t and 05streamscan.t files:
> >> 1) change all references to 'clamsock' to '/tmp/clamsock' (should be 3
> >> places in each file: in the loop, during File::Scan::ClamAV
> >> instantiation and unlink)
> >> 2) change the for loop count from 10 to 60 (as clamd takes a while to
> >> load) so,
> >> for (1..10)
> >> to
> >> for (1..60)
> >>
> >> #step 4
> >> cd ..
> >> (back to the root build dir)
> >>
> >> # step 5
> >> (run make test to run the test suite) e.g.:
> >>
> >> xxxx at xxxx:.cpan/build/File-Scan-ClamAV-1.91-O_dSGE# make test
> >> PERL_DL_NONLAZY=1 CLAMD_PATH=/usr/sbin /usr/bin/perl
> >> "-MExtUtils::Command::MM" "-e" "test_harness(0, 'blib/lib',
> >> ' blib/arch')" t/*.t
> >> t/00basic.t ....... ok
> >> t/01ping.t ........ ok
> >> t/02reload.t ...... ok
> >> t/03quit.t ........ ok
> >> t/04scan.t ........ ok
> >> t/05streamscan.t .. ok
> >> t/pod-coverage.t .. skipped: Test::Pod::Coverage 1.00 required for
> >> testing POD coverage
> >> t/pod.t ........... skipped: Test::Pod 1.00 required for testing POD
> >> All tests successful.
> >> Files=8, Tests=27, 187 wallclock secs ( 0.09 usr 0.04 sys + 174.55
> >> cusr 4.58 csys = 179.26 CPU)
> >> Result: PASS
> >> xxxx at xxxx:.cpan/build/File-Scan-ClamAV-1.91-O_dSGE#
> >>
> >> # step 6
> >> (run make install to install the modules)
> >> make install
> >>
> >> # step 7
> >> exit
> >> quit
> >>
> >> Hope this helps,
> >>
> >> Ant
> >> _______________________________________________
> >> Help us build a comprehensive ClamAV guide:
> >> https://github.com/vrtadmin/clamav-faq
> >> http://www.clamav.net/support/ml
> > Hmm, made the changes as noted:
> >
> > root at localhost:~/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf# make test
> > PERL_DL_NONLAZY=1 CLAMD_PATH=/usr/sbin /usr/bin/perl
> > "-MExtUtils::Command::MM" "-e" "test_harness(0, 'blib/lib',
> > 'blib/arch')" t/*.t
> > t/00basic.t ....... ok
> > t/01ping.t ........ ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/01ping.t ........ 1/3 # Failed test 2 in t/01ping.t at line 26
> > # t/01ping.t line 26 is: ok($av->ping);
> > t/01ping.t ........ Failed 1/3 subtests
> > t/02reload.t ...... ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > ^Cmake: *** [test_dynamic] Interrupt
> >
> > root at localhost:~/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf# make test
> > PERL_DL_NONLAZY=1 CLAMD_PATH=/usr/sbin /usr/bin/perl
> > "-MExtUtils::Command::MM" "-e" "test_harness(0, 'blib/lib',
> > 'blib/arch')" t/*.t
> > t/00basic.t ....... ok
> > t/01ping.t ........ ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/01ping.t ........ 1/3 # Failed test 2 in t/01ping.t at line 26
> > # t/01ping.t line 26 is: ok($av->ping);
> > t/01ping.t ........ Failed 1/3 subtests
> > t/02reload.t ...... ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/02reload.t ...... 1/3 # Failed test 2 in t/02reload.t at line 25
> > # t/02reload.t line 25 is: ok($av->reload);
> > t/02reload.t ...... Failed 1/3 subtests
> > t/03quit.t ........ ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/03quit.t ........ 1/4 # Failed test 2 in t/03quit.t at line 31
> > # t/03quit.t line 31 is: ok($av->quit);
> > t/03quit.t ........ Failed 1/4 subtests
> > t/04scan.t ........ ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/04scan.t ........ 1/8 # Test 4 got: "" (t/04scan.t at line 36)
> > # Expected: "1" (Didn't
> > detect /home/chris/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf/testfiles/clamavtest)
> > # t/04scan.t line 36 is: ok(exists($results{"$testdir/clamavtest"}), 1,
> > "Didn't detect $testdir/clamavtest");
> > # Test 5 got: "" (t/04scan.t at line 37)
> > # Expected: "1" (Didn't
> > detect /home/chris/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf/testfiles/clamavtest.zip)
> > # t/04scan.t line 37 is:
> > ok(exists($results{"$testdir/clamavtest.zip"}), 1, "Didn't detect
> > $testdir/clamavtest.zip");
> > # Test 6 got: "" (t/04scan.t at line 38)
> > # Expected: "1" (Didn't
> > detect /home/chris/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf/testfiles/clamavtest.gz)
> > # t/04scan.t line 38 is: ok(exists($results{"$testdir/clamavtest.gz"}),
> > 1, "Didn't detect $testdir/clamavtest.gz");
> > t/04scan.t ........ Failed 3/8 subtests
> > t/05streamscan.t .. ERROR: LOCAL: Socket file /clamsock could not be
> > bound: Permission denied
> > t/05streamscan.t .. 1/8 # Test 5 got: <UNDEF> (t/05streamscan.t at line
> > 43)
> > # Expected: "FOUND"
> > # t/05streamscan.t line 43 is: ok($ans, 'FOUND');
> > # Test 6 got: <UNDEF> (t/05streamscan.t at line 44)
> > # Expected: "ClamAV-Test-Signature"
> > # t/05streamscan.t line 44 is: ok($vir, 'ClamAV-Test-Signature');
> > t/05streamscan.t .. Failed 2/8 subtests
> > t/pod-coverage.t .. ok
> > t/pod.t ........... ok
> >
> > Test Summary Report
> > -------------------
> > t/01ping.t (Wstat: 0 Tests: 3 Failed: 1)
> > Failed test: 2
> > t/02reload.t (Wstat: 0 Tests: 3 Failed: 1)
> > Failed test: 2
> > t/03quit.t (Wstat: 0 Tests: 4 Failed: 1)
> > Failed test: 2
> > t/04scan.t (Wstat: 0 Tests: 8 Failed: 3)
> > Failed tests: 4-6
> > t/05streamscan.t (Wstat: 0 Tests: 8 Failed: 2)
> > Failed tests: 5-6
> > Files=8, Tests=29, 301 wallclock secs ( 0.04 usr 0.01 sys + 56.64 cusr
> > 1.95 csys = 58.64 CPU)
> > Result: FAIL
> > Failed 5/8 test programs. 8/29 subtests failed.
> > make: *** [test_dynamic] Error 255
> >
> > I have /tmp under:
> >
> > root at localhost:/# cd root
> > root at localhost:/root# ls -l
> > total 8
> > drwxr-xr-x 2 root root 4096 Jul 15 07:49 Desktop
> > drwxr-xr-x 2 root root 4096 Jul 22 10:22 tmp
> >
> > root at localhost:/root# cd ..
> > root at localhost:/# ls -l
> > total 129
> > drwxr-xr-x 2 root root 4096 Jul 12 20:32 bin
> > drwxr-xr-x 4 root root 1024 Jul 17 08:22 boot
> > drwxrwxr-x 2 root root 4096 Jul 12 19:52 cdrom
> > drwxr-xr-x 16 root root 4300 Jul 21 22:30 dev
> > drwxr-xr-x 152 root root 12288 Jul 21 22:30 etc
> > -rw-r--r-- 1 root root 4777 Jan 11 2008 GPG.KEY
> > drwxr-xr-x 3 root root 4096 Jul 12 19:53 home
> > lrwxrwxrwx 1 root root 33 Jul 17 08:22 initrd.img ->
> > boot/initrd.img-3.13.0-32-generic
> > lrwxrwxrwx 1 root root 33 Jul 12 20:33 initrd.img.old ->
> > boot/initrd.img-3.13.0-30-generic
> > drwxr-xr-x 23 root root 4096 Jul 12 19:58 lib
> > drwxr-xr-x 2 root root 4096 Apr 16 20:21 lib64
> > drwx------ 2 root root 16384 Jul 12 19:45 lost+found
> > drwxr-xr-x 3 root root 4096 Jul 12 21:05 media
> > drwxr-xr-x 2 root root 4096 Apr 10 17:12 mnt
> > drwxr-xr-x 7 root root 4096 Jul 16 15:39 nonexisting
> > drwxr-xr-x 2 root root 4096 Apr 16 20:21 opt
> > dr-xr-xr-x 239 root root 0 Jul 20 17:45 proc
> > -rw-r--r-- 1 root root 108 Jul 14 09:13 razor-agent.log
> > drwx------ 21 root root 4096 Jul 22 10:22 root
> > drwxr-xr-x 28 root root 880 Jul 21 07:37 run
> > drwxr-xr-x 2 root root 12288 Jul 12 20:28 sbin
> > drwxr-xr-x 2 root root 4096 Apr 16 20:21 srv
> > dr-xr-xr-x 13 root root 0 Jul 20 17:45 sys
> > drwxrwxrwt 12 root root 20480 Jul 22 10:26 tmp
> > drwxr-xr-x 12 root root 4096 Jul 14 20:50 usr
> > drwxr-xr-x 17 root root 4096 Jul 16 13:37 var
> > lrwxrwxrwx 1 root root 30 Jul 17 08:22 vmlinuz ->
> > boot/vmlinuz-3.13.0-32-generic
> > lrwxrwxrwx 1 root root 30 Jul 12 20:33 vmlinuz.old ->
> > boot/vmlinuz-3.13.0-30-generic
> > -rw-r--r-- 1 root root 2165 Jul 13 14:07 webmin-setup.out
> >
> > and to be sure I made one in my /home/chris folder:
> >
> > drwxrwxr-x 2 chris chris 4096 Jul 22 10:31 tmp
> >
> > So, where did I go wrong?
> >
> > Thanks
> > Chris
> >
> >
> >
> > _______________________________________________
> > Help us build a comprehensive ClamAV guide:
> > https://github.com/vrtadmin/clamav-faq
> > http://www.clamav.net/support/ml
>
> From the looks of it you are attempting to connect to the socket on
> /clamsock and not /tmp/clamsock. In the *.t files there should be lines
> like:
>
> my $av = new File::Scan::ClamAV(port => "clamsock");
>
> This needs to change to
>
> my $av = new File::Scan::ClamAV(port => "/tmp/clamsock");
>
> Also double check the change to mkconf.pl is:
> my $dir = '/tmp/';
Ok, found the problem. In mkconf the line
LocalSocket $dir /tmp/clamsock
I had just set it as /tmp/ after setting it to /tmp/clamsock and
stopping apparmor
root at localhost:~/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf# make test
PERL_DL_NONLAZY=1 CLAMD_PATH=/usr/sbin /usr/bin/perl
"-MExtUtils::Command::MM" "-e" "test_harness(0, 'blib/lib',
'blib/arch')" t/*.t
t/00basic.t ....... ok
t/01ping.t ........ ok
t/02reload.t ...... ok
t/03quit.t ........ ok
t/04scan.t ........ ok
t/05streamscan.t .. ok
t/pod-coverage.t .. ok
t/pod.t ........... ok
All tests successful.
Files=8, Tests=29, 84 wallclock secs ( 0.05 usr 0.02 sys + 58.08 cusr
2.46 csys = 60.61 CPU)
Result: PASS
root at localhost:~/.cpan/build/File-Scan-ClamAV-1.91-N3ENzf# make install
Manifying blib/man3/File::Scan::ClamAV.3pm
Installing /usr/local/share/perl/5.18.2/File/Scan/ClamAV.pm
Installing /usr/local/man/man3/File::Scan::ClamAV.3pm
Appending installation info to /usr/local/lib/perl/5.18.2/perllocal.pod
Now to make sure the rest of the settings are correct and wait for
something to hit.
I sure do thank you for this I would have never figured it out.
Chris
--
Chris
31.11°N 97.89°W (Elev. 1092 ft)
13:06:59 up 1 day, 19:21, 4 users, load average: 0.06, 0.24, 0.40
Ubuntu 14.04 LTS, kernel 3.13.0-32-generic
More information about the clamav-users
mailing list